大师作文网有人知道有关PLC的英语文章吗?
来源：学生作业帮 编辑：大师作文网作业帮 分类：英语作业 时间：2024/11/19 23:01:54
有人知道有关PLC的英语文章吗?
Programmable logic controller
A programmable logic controller (PLC),or programmable controller is a digital computer used for automation of industrial processes,such as control of machinery on factory assembly lines.Unlike general-purpose computers,the PLC is designed for multiple inputs and output arrangements,extended temperature ranges,immunity to electrical noise,and resistance to vibration and impact.Programs to control machine operation are typically stored in battery-backed or non-volatile memory.A PLC is an example of a real time system since output results must be produced in response to input conditions within a bounded time,otherwise unintended operation will result.
PLC and Programmable Logic Controller are registered trademarks of the Allen-Bradley Company,although they are widely used generically.
Features
The main difference from other computers is that PLC are armored for severe condition (dust,moisture,heat,cold,etc) and have the facility for extensive input/output (I/O) arrangements.These connect the PLC to sensors and actuators.PLCs read limit switches,analog process variables (such as temperature and pressure),and the positions of complex positioning systems.Some even use machine vision.On the actuator side,PLCs operate electric motors,pneumatic or hydraulic cylinders,magnetic relays or solenoids,or analog outputs.The input/output arrangements may be built into a simple PLC,or the PLC may have external I/O modules attached to a computer network that plugs into the PLC.
PLCs were invented as replacements for automated systems that would use hundreds or thousands of relays,cam timers,and drum sequencers.Often,a single PLC can be programmed to replace thousands of relays.Programmable controllers were initially adopted by the automotive manufacturing industry,where software revision replaced the re-wiring of hard-wired control panels when production models changed.
Many of the earliest PLCs expressed all decision making logic in simple ladder logic which appeared similar to electrical schematic diagrams.The electricians were quite able to trace out circuit problems with schematic diagrams using ladder logic.This program notation was chosen to reduce training demands for the existing technicians.Other early PLCs used a form of instruction list programming,based on a stack-based logic solver.
The functionality of the PLC has evolved over the years to include sequential relay control,motion control,process control,distributed control systems and networking.The data handling,storage,processing power and communication capabilities of some modern PLCs are approximately equivalent to desktop computers.PLC-like programming combined with remote I/O hardware,allow a general-purpose desktop computer to overlap some PLCs in certain applications.
Under the IEC 61131-3 standard,PLCs can be programmed using standards-based programming languages.A graphical programming notation called Sequential Function Charts is available on certain programmable controllers.
A programmable logic controller (PLC),or programmable controller is a digital computer used for automation of industrial processes,such as control of machinery on factory assembly lines.Unlike general-purpose computers,the PLC is designed for multiple inputs and output arrangements,extended temperature ranges,immunity to electrical noise,and resistance to vibration and impact.Programs to control machine operation are typically stored in battery-backed or non-volatile memory.A PLC is an example of a real time system since output results must be produced in response to input conditions within a bounded time,otherwise unintended operation will result.
PLC and Programmable Logic Controller are registered trademarks of the Allen-Bradley Company,although they are widely used generically.
Features
The main difference from other computers is that PLC are armored for severe condition (dust,moisture,heat,cold,etc) and have the facility for extensive input/output (I/O) arrangements.These connect the PLC to sensors and actuators.PLCs read limit switches,analog process variables (such as temperature and pressure),and the positions of complex positioning systems.Some even use machine vision.On the actuator side,PLCs operate electric motors,pneumatic or hydraulic cylinders,magnetic relays or solenoids,or analog outputs.The input/output arrangements may be built into a simple PLC,or the PLC may have external I/O modules attached to a computer network that plugs into the PLC.
PLCs were invented as replacements for automated systems that would use hundreds or thousands of relays,cam timers,and drum sequencers.Often,a single PLC can be programmed to replace thousands of relays.Programmable controllers were initially adopted by the automotive manufacturing industry,where software revision replaced the re-wiring of hard-wired control panels when production models changed.
Many of the earliest PLCs expressed all decision making logic in simple ladder logic which appeared similar to electrical schematic diagrams.The electricians were quite able to trace out circuit problems with schematic diagrams using ladder logic.This program notation was chosen to reduce training demands for the existing technicians.Other early PLCs used a form of instruction list programming,based on a stack-based logic solver.
The functionality of the PLC has evolved over the years to include sequential relay control,motion control,process control,distributed control systems and networking.The data handling,storage,processing power and communication capabilities of some modern PLCs are approximately equivalent to desktop computers.PLC-like programming combined with remote I/O hardware,allow a general-purpose desktop computer to overlap some PLCs in certain applications.
Under the IEC 61131-3 standard,PLCs can be programmed using standards-based programming languages.A graphical programming notation called Sequential Function Charts is available on certain programmable controllers.