大师作文网我的英语不好,帮我把下面的这段话翻译成英语嘛,谢谢哈,
来源：学生作业帮 编辑：大师作文网作业帮 分类：综合作业 时间：2024/11/10 19:55:27
我的英语不好,帮我把下面的这段话翻译成英语嘛,谢谢哈,
就是下面的内容:
我们根据以前的经验判断.
正打开时出现同样的问题：Application Error. 不能进去,所以从这里我知道我先得把软件问题解决.目前较容易的就是重装FmNT软件,只需卸载现有软件重新安装.安装完后发现软件可以进入,下一步我开始测试硬件故障,所以我开始配置各个硬件装置, 如：COM2 conveyor; COM3 scale; COM4 heater. 在这个过程中我发现从COM3 开始就已经配置不了,显示打开此端口错误,后来我开始在控制面板的 PORT 中找COM 口信息,发现从COM3开始都消失了,所以我自己开始 配置COM3 到COM6 .重启系统后发现问题依旧,我就知道是我们的COM 口卡坏了,因此根本原因就出现在4 PORT BLASTRONIX 卡上.
就是下面的内容:
我们根据以前的经验判断.
正打开时出现同样的问题：Application Error. 不能进去,所以从这里我知道我先得把软件问题解决.目前较容易的就是重装FmNT软件,只需卸载现有软件重新安装.安装完后发现软件可以进入,下一步我开始测试硬件故障,所以我开始配置各个硬件装置, 如：COM2 conveyor; COM3 scale; COM4 heater. 在这个过程中我发现从COM3 开始就已经配置不了,显示打开此端口错误,后来我开始在控制面板的 PORT 中找COM 口信息,发现从COM3开始都消失了,所以我自己开始 配置COM3 到COM6 .重启系统后发现问题依旧,我就知道是我们的COM 口卡坏了,因此根本原因就出现在4 PORT BLASTRONIX 卡上.
We,according to the experience judgement in the past.
Present the same question while opening:Application Error.Can't enter ,so I know from here I must solve the problem of the software first .An easier one resets FmNT software and only needs to unload the existing software to reinstallate at present.Find software can enter ,the next step I is it test hardware trouble to begin after the installation,so I begin to dispose each hardware device ,for instance:COM2 conveyor; COM3 scale; COM4 heater.I find in this course that begin not to dispose from COM3 ,show that opens this port mistake,COM mouth information that I began let of PORT of the control panel,found that began to disappear from COM3 later on,so I myself begin to dispose COM3 to COM6.Pinpoint the problems to remain unchanged after opening the system again,I know COM a card of ours is out of order,so the basic reason appears on 4 PORT BLASTRONIX card .
Present the same question while opening:Application Error.Can't enter ,so I know from here I must solve the problem of the software first .An easier one resets FmNT software and only needs to unload the existing software to reinstallate at present.Find software can enter ,the next step I is it test hardware trouble to begin after the installation,so I begin to dispose each hardware device ,for instance:COM2 conveyor; COM3 scale; COM4 heater.I find in this course that begin not to dispose from COM3 ,show that opens this port mistake,COM mouth information that I began let of PORT of the control panel,found that began to disappear from COM3 later on,so I myself begin to dispose COM3 to COM6.Pinpoint the problems to remain unchanged after opening the system again,I know COM a card of ours is out of order,so the basic reason appears on 4 PORT BLASTRONIX card .