大师作文网英语翻译无合模线纺纱管锭塑料模具设计该无合模线纺纱管锭塑料注塑模具设计的关键是该模具必须带有斜抽芯装置,并要准确确定合模
来源：学生作业帮 编辑：大师作文网作业帮 分类：英语作业 时间：2024/10/04 06:37:58
英语翻译
无合模线纺纱管锭塑料模具设计
该无合模线纺纱管锭塑料注塑模具设计的关键是该模具必须带有斜抽芯装置,并要准确确定合模方向,且保证合模线不能在管子的外表面.出于用途考虑,它是用于缠绕棉纱,这就要求管子外表面足够光滑,本文就解决以上设计问题给予说明.并通过对塑件材料,质量 体积的分析与计算,合理选用注塑机,并对各个参数进行了校核,设计出一副合理,经济,适用的塑料注塑模具.
注塑模；斜抽芯；无合模线
无合模线纺纱管锭塑料模具设计
该无合模线纺纱管锭塑料注塑模具设计的关键是该模具必须带有斜抽芯装置,并要准确确定合模方向,且保证合模线不能在管子的外表面.出于用途考虑,它是用于缠绕棉纱,这就要求管子外表面足够光滑,本文就解决以上设计问题给予说明.并通过对塑件材料,质量 体积的分析与计算,合理选用注塑机,并对各个参数进行了校核,设计出一副合理,经济,适用的塑料注塑模具.
注塑模；斜抽芯；无合模线
No mold line of spindles spinning plastic mold design
The nil-ray tube spindles spinning plastic injection mold design,the key is to die with the ramp-pumping device and to accurately determine the direction of mold and mold guarantee Line is not in the external surface of the tubes.For purposes consider that it is used for winding yarn,which calls for the tubes outer surface smooth enough,This article solve design problems to provide an explanation.And pieces of plastic materials,the quality of analysis and volume calculation,a reasonable selection of injection molding machinery,as well as various parameters of the check,design a reasonable,affordable,suitable plastic injection mold.
Injection Mold; Pumped-ramp; No mold line
The nil-ray tube spindles spinning plastic injection mold design,the key is to die with the ramp-pumping device and to accurately determine the direction of mold and mold guarantee Line is not in the external surface of the tubes.For purposes consider that it is used for winding yarn,which calls for the tubes outer surface smooth enough,This article solve design problems to provide an explanation.And pieces of plastic materials,the quality of analysis and volume calculation,a reasonable selection of injection molding machinery,as well as various parameters of the check,design a reasonable,affordable,suitable plastic injection mold.
Injection Mold; Pumped-ramp; No mold line
英语翻译无合模线纺纱管锭塑料模具设计该无合模线纺纱管锭塑料注塑模具设计的关键是该模具必须带有斜抽芯装置,并要准确确定合模
纺纱娘是怎样纺纱的?
什么是环锭纺纱
何为环锭纺纱?比如说c16's 半精舒环锭纺纱.锭纺纱是什么意思?
我最近要做注塑模具设计 题目是塑料端盖注塑模具设计,是个很久的题目了.我们图书馆借不到相关的书籍了
一套带有金属嵌件的注塑模,金属嵌件为铜螺丝,在设计模具时,怎么样保证塑料不进入螺纹
英语翻译摘 要本次模具设计的内容是“矿泉水瓶盖注塑模的设计”.之所以选择这个设计题目主要有两方面意义：1、瓶盖是带螺纹的
做好模具了 该注塑了 不知道该用什么塑料好,
注塑模具设计流程1.小弟想知道注塑模具的设计流程,从接到产品图纸到试模?2.客户提供的产品图一般是2d的还是3d的?3.
注塑模具弹簧长度怎么算?如行程是40,该定多长的弹簧?
注塑模具设计的步骤
纺纱断头多,是因为钢丝圈太重吗?