英语翻译1、单次切割加工时,根据加工表面光度要求,脉宽一般为5 80us,脉间一般为脉宽的5倍,脉宽加大可以提高加工速度
来源:学生作业帮 编辑:大师作文网作业帮 分类:英语作业 时间:2024/09/24 13:17:38
英语翻译
1、单次切割加工时,根据加工表面光度要求,脉宽一般为5 80us,脉间一般为脉宽的5倍,脉宽加大可以提高加工速度,但表面粗糙度会增加,减速小脉间,一般不影响加工表面的光洁度,可以提高加工效率,但是过小的脉间,会使加工不稳定,严重时会烧断钼丝;对于大厚度工件或是难加工的工件一般采用大脉宽(60-80us)与大脉间(脉宽的7-10倍),短路电流为45以上,平均加工电流一般不大于3.0A.
2、加工电压一般采用1H,当加工大厚度工件及导电性不好的材料用2H或是改变变压器上的接线,采用更高的加工电压进行加工.
3、多次切割一般采用三次切割即可,第1次的偏移量一般为0.05~0.08mm,第2次的偏移量一般为0.005~0.015mm,最后一次必需为0mm.
4、采用前阶梯波可以降低钼丝损耗,一般选用B、C、D档.
就只有25分
1、单次切割加工时,根据加工表面光度要求,脉宽一般为5 80us,脉间一般为脉宽的5倍,脉宽加大可以提高加工速度,但表面粗糙度会增加,减速小脉间,一般不影响加工表面的光洁度,可以提高加工效率,但是过小的脉间,会使加工不稳定,严重时会烧断钼丝;对于大厚度工件或是难加工的工件一般采用大脉宽(60-80us)与大脉间(脉宽的7-10倍),短路电流为45以上,平均加工电流一般不大于3.0A.
2、加工电压一般采用1H,当加工大厚度工件及导电性不好的材料用2H或是改变变压器上的接线,采用更高的加工电压进行加工.
3、多次切割一般采用三次切割即可,第1次的偏移量一般为0.05~0.08mm,第2次的偏移量一般为0.005~0.015mm,最后一次必需为0mm.
4、采用前阶梯波可以降低钼丝损耗,一般选用B、C、D档.
就只有25分
1,single cutting processing,according to machining surface photometric requirements,pulse width is commonly 5 80us,interveinal general for pulse width 5 times,pulse width increasing can improve the processing speed,but the surface roughness increases,slowing small interveinal generally do not affect machining surface finish,can increase the processing efficiency,but too small interveinal,can make the processing is not stable,severe burn when cut molybdenum wire; For large thickness or difficult-to-machine artifacts of the workpiece generally adopted pulse width (60 - big 80us) and big interveinal (pulse width 7 to 10 times),short-circuit current 45 above,average processing current general no greater than 3.0 A.
2,processing voltage generally USES 1H,when processing large thickness workpiece and conductivity bad material to use 2H or change of the connection,the transformer higher machining voltage for machining.
3,multiple cutting generally USES three times,the first time cutting can offset generally is 0.05 0.08 mm,second offset is commonly 0.005 0.015 mm,for the last time 0mm necessary.
4,the previous ladder wave can reduce molybdenum wire losses,the general selection B,C,D gear.
再问: 有道翻译 改改吧少年 改通顺了
再答: 行稍等
再问: 继续追问 - - 有10分呐 有了都给你呐 去先吃饭去了
再答: 1, single cutting processing, according to machining surface photometric requirements, pulse width is commonly 5 ~ 80us, interveinal general for pulse width 5 times, Increasing pulse width can improve the cutting speed, but that will increase the surface roughness , smaller interveinal generally do not affect machining surface finish, and can increase the processing efficiency, but too small interveinal, can make the processing is not stable, severe burn when cut molybdenum wire; For large thickness or difficult-to-machine artifacts of the workpiece generally adopted pulse width (60 - big 80us) and big interveinal (pulse width 7 to 10 times), short-circuit current 45 above, average processing current general smaller than 3.0 A. 2, processing voltage generally USES 1H, when processing large thickness workpiece and conductivity bad material to use 2H or change of the connection, the transformer higher machining voltage for machining. 3, multiple cutting generally uses three times, the first time cutting can offset generally is 0.05 ~ 0.08 mm, second offset is commonly 0.005 ~ 0.015 mm, for the last time 0mm necessary. 4, the previous ladder wave can reduce molybdenum wire losses, the general selection B, C, D gear. 这样可以了,虽说不是很专业,但不影响阅读了
再问: 好吧追问3次 了咩
2,processing voltage generally USES 1H,when processing large thickness workpiece and conductivity bad material to use 2H or change of the connection,the transformer higher machining voltage for machining.
3,multiple cutting generally USES three times,the first time cutting can offset generally is 0.05 0.08 mm,second offset is commonly 0.005 0.015 mm,for the last time 0mm necessary.
4,the previous ladder wave can reduce molybdenum wire losses,the general selection B,C,D gear.
再问: 有道翻译 改改吧少年 改通顺了
再答: 行稍等
再问: 继续追问 - - 有10分呐 有了都给你呐 去先吃饭去了
再答: 1, single cutting processing, according to machining surface photometric requirements, pulse width is commonly 5 ~ 80us, interveinal general for pulse width 5 times, Increasing pulse width can improve the cutting speed, but that will increase the surface roughness , smaller interveinal generally do not affect machining surface finish, and can increase the processing efficiency, but too small interveinal, can make the processing is not stable, severe burn when cut molybdenum wire; For large thickness or difficult-to-machine artifacts of the workpiece generally adopted pulse width (60 - big 80us) and big interveinal (pulse width 7 to 10 times), short-circuit current 45 above, average processing current general smaller than 3.0 A. 2, processing voltage generally USES 1H, when processing large thickness workpiece and conductivity bad material to use 2H or change of the connection, the transformer higher machining voltage for machining. 3, multiple cutting generally uses three times, the first time cutting can offset generally is 0.05 ~ 0.08 mm, second offset is commonly 0.005 ~ 0.015 mm, for the last time 0mm necessary. 4, the previous ladder wave can reduce molybdenum wire losses, the general selection B, C, D gear. 这样可以了,虽说不是很专业,但不影响阅读了
再问: 好吧追问3次 了咩
英语翻译1、单次切割加工时,根据加工表面光度要求,脉宽一般为5 80us,脉间一般为脉宽的5倍,脉宽加大可以提高加工速度
英语翻译1 引言一般把单向送丝速度低于0.2m/s的电火花线切割加工方法称为慢走丝线切割加工.慢走丝线切割具有切割尺寸精
(1)某齿条型刀具的模数为5mm,加工齿数为46的直齿圆柱齿轮.加工时刀具中线到轮坯中心的距离为120mm,加工出来的齿
一道求加工周期的计算题,某产品生产5件,经过4道工序,每道工序加工的单件工时分别为10分钟,8分
一块长70cm,宽15cm,厚5cm的木料,加工时把长,宽,厚各刨去一厘米,加工后体积减少了多少
怎样提高线切割加工速度
锪钻加工孔口端面后得到的表面粗糙度一般为多少~不是精锪.
什么是电火花加工过程中的极性效应?何为正极性加工?何为负极性加工?加工时应如何正确选择加工极性?并
某传统食品加工过程中,一般在1kg面粉中加1g明矾[已知:明矾的化学式为KAl(so4)2*12H2O,...
数学问题: 1、某车间接到一批加工任务,计划每天加工120件,可以如期完成,实际加工时每天多加工20件
线切割加工时间的计算宽35mm,厚30mm,m2.5的齿条,在中走丝400*500的线切割上割下一根得用多长时间?2.5
编制加工如图所示的线切割加工3B代码程序.已知线切割加工用的电极丝直径为0.16mm,单边放电间隙为0.02mm